Plumbing Essentials: A Prerequisite for Installing a Bathtub
Plumbing Essentials: A Prerequisite for Installing a Bathtub
Blog Article
Right here in the next paragraph you'll find a good deal of good resources in relation to How to Install a Bathtub Yourself.
Installing a tub isn't precisely rocket science, however it does require strong plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a new one is additionally a moderately difficult project. If the old tub is readily obtainable, the project can move immediately; if you have to open up a wall surface to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and set in the new one. Make certain you have actually certified on your own for the task and also fit attempting it. Rather than hiring a professional to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you may need an expert plumber to make tube links.
This write-up will certainly help you set up a brand-new bathtub in your bathroom if you have actually currently acquired a new tub and do not require to alter the setup of your previous water system pipes.
Your devices and also material list need to consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be rather troublesome because of the limited access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Before moving on to fit the new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washers are in area between the tap as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The previous type needs to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Making use of both wood boards under its feet, place the bathtub in the needed setting. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four little points.
The following goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bath tub until the level checks out degree.
To install taps, fit the bottom of the furthest adaptable tap connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water system and also check all joints and brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and additionally inspect the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the tub must wait till the bathtub has been made use of at least once as this will resolve it right into its last placement.
Preparing for the Installation
To start with, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps system to avoid pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about issues with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and fittings. They are sold in tubes and cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to allow for the motion experienced when the tub is in usage. The sealer can split fairly very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the marketplace. It is recommended to fit the tiles utilizing waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was brought to that editorial on Tools You Need to Install a New Bathtub from a good friend on a different blog. Sharing is good. Helping people is fun. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Contact for excellence. Report this page